Boost-Up-Internet-Speed-Without Software

Boost-Up-Internet-Speed-Without Software


Above 90% computers all over the world run Windows... and hence another computer trick.


FACT
But do you know that about 20% of your internet bandwidth is reserved by Microsoft.
---------------------------------------------------------------------------------------------------------
Uses of Reserved Bandwidth
** Windows Automatic Updates rely on this reserved bandwidth.
** Fast loading Microsoft Websites
** Sending Error Reports
** Online Help support in Microsoft Office
---------------------------------------------------------------------------------------------------------
But this can be recovered back...
---------------------------------------------------------------------------------------------------------
The Remedy
** Start >> Run
** Type gpedit.msc
** This opens the Policy Editor
** Now, Local Computer Policy >> Computer Configuration
** Then, Administrative Templates >> Network
** Now, click on QOS Packet Scheduler
** Now, on Right hand side
** Double Click Limit reservable bandwidth
** Now in Setting Tab


********************* NOTE **********************
It says : Not Configured
Reality : The Explain Tab says "By default, the Packet Scheduler limits the system to 20 percent of the bandwidth of a connection"
************************************************** *


** So, on Setting Tab select Enabled
** Now, change Bandwidth limit (%) to 0 (Zero)


********************** NOTE ********************
Misconcept : This don't means that you won't be able to communicate with Microsoft or any its services !!!
Actually : This reserved Bandwidth is only to accelerate Microsoft internet connections more than other connections !!!
************************************************** **


** Click OK !!!




That's All !!!

অনলাইনে ফন্ট পরিবর্তন

কম্পিউটারে ইউনিকোড ফন্ট ইন্সটল করা না থাকলে সাধারণত ইউনিকোডে লেখা ফাইল পড়া যায় না। আবার বিজয় ফন্ট ইন্সটল না থাকলে বিজয় ব্যবহার করে লেখা ফাইল পড়া যায় না। অনলাইনে এক ফন্ট থেকে অন্য ফন্টে পরিবর্তন করতে প্রথমে এই ওয়েবসাইটে যান। ইউনিকোড থেকে বিজয় ফন্টে পরিবর্তন করার জন্য প্রথম বক্স আপনার লেখা পেস্ট করুন এবং 'পুরনো বাংলায় নিচে বদলে আনো' অপশনে ক্লিক করুন। বিজয় থেকে ইউনিকোডে কনভার্ট করার জন্য আপনার লেখা পেস্ট করে এবং ইউনিকোডে 'ওপরে বদলে নাও' অপশনে ক্লিক করুন।

Reasons for not detecting hard disk

The most common reason is a loose or badly connected data cable. Make sure the data cable is plugged in properly, both into the hard disk, as well as the motherboard.

The same goes for power cable, so check that as well. Also, make sure that the red lines on the data cable and power cable are adjacent to each other.

One you’ve ruled out any cable problems, check the jumper setting on the drives. If two drives are connected to a port, make sure one is set as master and the other as Slave, or else both are set to Cable Select.

Next, make sure your drive controllers on your motherboard are not disabled. These controllers control IDE devices, and without them the BIOS cannot detect the drives.

Go to the BIOS setup, and under the Integrated Peripherals menu, make sure that ‘On Board HDC’ is enabled for both Primary and Secondary channels.

Also ensure that all drive types are set to AUTO under the Standard CMOS Setting.
If you are not comfortable with changing the BIOS values, just reset the BIOS to factory defaults.

When all else fails, so has your hard disk send it to a technician for servicing.
I hope this Guide will solve your hard disk detection problem on your motherboard bios.